10.1007/s40095-021-00466-1

Optimization of thermal efficiency in traditional clay-based buildings in hot–dry locations. Case study: the south-eastern region of Morocco

  • Ali Lamrani Alaoui1,
  • Abdel-illah Amrani*1,
  • Ahmed Alami Merrouni2,
  • Abdelkarim Daoudia3,
  • Youssef El Hassouani1,
  1. Equipe des Energies Nouvelles et Ingénierie des Matériaux (ENIM), Laboratoire de Sciences et Techniques de l’Ingénieur (LSTI), Faculté des Sciences et Techniques, Université Moulay Ismail, Errachidia, 52000, MA
  2. Materials Science, New Energies and Applications Research Group, LPTPME Laboratory, Department of physics, Faculty of sciences, Mohammed 1st, University, Oujda, 60000, MA
  3. Equipe de PhysiqueThéorique et Modélisation (PTM), Laboratoire de Sciences et Techniques de l’Ingénieur, Faculté des Sciences et Techniques, Université Moulay Ismail, Errachidia, 52000, MA

Published in Issue 2022-01-17

How to Cite

Lamrani Alaoui, A., Amrani, A.- illah, Alami Merrouni, A., Daoudia, A., & El Hassouani, Y. (2022). Optimization of thermal efficiency in traditional clay-based buildings in hot–dry locations. Case study: the south-eastern region of Morocco. International Journal of Energy and Environmental Engineering, 13(2 (June 2022). https://doi.org/10.1007/s40095-021-00466-1
Crossref
Scopus
Google Scholar
Europe PMC

Abstract

Abstract In Morocco, the building sector is responsible for more than 30% of the country’s energy consumption. The latter tends to increase significantly in parallel with the high urbanization level, which requires the improvement of the thermal building’s efficiency and to reduce their energy consumption. In this paper, we followed two approaches: (i) an experimental study aiming at the determination of the thermal parameters characterizing the local construction materials usually used in the buildings in the south-east of Morocco. (ii) TRNSYS simulations to predict and optimize the thermal performances for two types of building in this region. After that, particular interest was given to treat the effect of the roof thickness and inclination on the average daily temperature evolution and the effect on the consumption of energy cooling and heating. Additionally, the energy consumption of the proposed building has been calculated and compared to the regular ones. Results show that the building based on clay and traditional construction materials provides more thermal comfort in comparison to the brick building. This is manifested by a temperature drop of 6.5% during the summer. Furthermore, this type of construction reduces the annual energy consumption by 27%. On the other hand, an increase of the reed layers up to five may reduce the temperature by 2 °C, thus improving the thermal efficiency of buildings. Besides, the integration of a roof with an inclination α = 30° within the clay construction reduces the energy consumption by 9%.

Keywords

  • Thermal efficiency,
  • South-east Morocco,
  • Clay building,
  • Local materials

References

  1. Zohuri (2020) Woodhead Publishing Series in Energy Nuclear Reactor Technology Development and Utilization https://doi.org/10.1016/B978-0-12-818483-7.00002-0
  2. Touili et al. (2019) Performance analysis of large scale grid connected PV plants in the MENA region (pp. 139-148) https://doi.org/10.4028/www.scientific.net/jera.42.139
  3. SerdarGenç et al. (2012) A review on wind energy and wind–hydrogen production in Turkey: a case study of hydrogen production via electrolysis system supplied by wind energy conversion system in Central Anatolian Turkey 16(9) (pp. 6631-6646) https://doi.org/10.1016/j.rser.2012.08.011
  4. AL-Homoud (2004) The effectiveness of thermal insulation in different types of buildings in hot climates 27(3) (pp. 235-247) https://doi.org/10.1177/1097196304038368
  5. Simona et al. (2017) Ion Increasing the energy efficiency of buildings by thermal insulation (pp. 393-399) https://doi.org/10.1016/j.egypro.2017.09.044
  6. Nourozi et al. (2020) Heat transfer model for energy-active windows–an evaluation of efficient reuse of waste heat in buildings (pp. 2318-2329) https://doi.org/10.1016/j.renene.2020.10.043
  7. Amrani et al. (2015) Modelling of natural convection with radiation in a triple-glazed ventilated window 29(4) (pp. 795-804) https://doi.org/10.2514/1.T4532
  8. Khosravi and Mahdavi (2020) A CFD-based parametric thermal performance analysis of supply air ventilated windows 14(9) https://doi.org/10.3390/en14092420
  9. Svoboda and Kubr (2010) Numerical simulation of heat transfer through hollow bricks in the vertical direction 34(4) (pp. 325-350) https://doi.org/10.1177/1744259110388266
  10. Amrani et al. (2019) Numerical investigation of coupled surface radiation and natural convection in a triangular shaped roof (Gabel Roof) under winter conditions (pp. 200-217) https://doi.org/10.4028/www.scientific.net/DDF.392.200
  11. Emin (2020) Numerical computation of laminar natural convection in triangular shaped cavities (pp. 27-38) https://doi.org/10.2495/AFM200031
  12. Amrani et al. (2018) Combined natural convection and thermal radiation heat transfer in a triangular enclosure with an inner rectangular body (pp. 49-68) https://doi.org/10.4028/www.scientific.net/DDF.384.49
  13. El-Sayed Ali and Alabdulkarem (2017) On thermal characteristics and microstructure of a new insulation material extracted from date palm trees surface fibers (pp. 276-284) https://doi.org/10.1016/j.jep.2016.12.017
  14. Jami et al. (2019) A review of the properties of hemp concrete for green building applications https://doi.org/10.1016/j.jclepro.2019.117852
  15. Kanellopoulos et al. (2017) Numerical analysis and modelling of heat transfer processes through perforated clay brick masonry walls (pp. 492-499) https://doi.org/10.1016/j.proenv.2017.03.112
  16. Bot et al. (2020) Performance assessment of a building integrated photovoltaic thermal system in mediterranean climate—a numerical simulation approach 13(11) https://doi.org/10.3390/en13112887
  17. Lafqir et al. (2020) Thermal performance of passive techniques integrated to a house and the concept of passive house in the six climates of Morocco https://doi.org/10.1080/23744731.2020.1805983
  18. Labouda, B., El Abbassi, I., Chikh, S.K., A-Moumen, D., Mamoudou, N.: The influence of TyphaAustralis as an insulation panel on the thermal performance of building. In: 6th International Conference on Energy and City of the Future (EVF’2019), vol 170, pp 01003 (2020)
  19. Silva et al. (2018) Characterization of hybrid pultruded structural products based on preforms (pp. 16-26) https://doi.org/10.1016/j.compositesb.2017.12.019
  20. Gounni and El Alami (2017) The optimal allocation of the PCM within a composite wall for surface temperature and heat flux reduction: an experimental approach (pp. 1488-1494) https://doi.org/10.1016/j.applthermaleng.2017.08.168
  21. http://www.solar-med-atlas.org/solarmed-atlas/map.htm#t=ghi
  22. . Accessed 18 June 2021 (2021)
  23. Eddouks et al. (2017) Ethnopharmacological survey of medicinal plants used in Daraa-Tafilalet region (Province of Errachidia) (pp. 516-530) https://doi.org/10.1016/j.jep.2016.12.017
  24. Laknizi et al. (2018) Performance analysis and optimal parameters of a direct evaporative pad cooling system under the climate conditions of Morocco https://doi.org/10.1016/j.csite.2018.11.013
  25. Ebrahimpour and Maerefat (2010) A method for generation of typical meteorological year 51(3) https://doi.org/10.1016/j.enconman.2009.10.002
  26. Klein et al. (1976) TRNSYS–a transient simulation program 82(1) (pp. 623-633)