10.1007/s40095-021-00387-z

Low-temperature synthesis of kerosene- and diesel-range fuels from waste plastics using natural potash catalyst

  • David John1,
  • Chikaodili E. Chukwuneke1,
  • Immaculata O. Onuigbo1,
  • Muhammad Falalu Yahaya1,
  • Bolade O. Agboola1,
  • Wan Jin Jahng*1,
  1. Department of Petroleum Chemistry, American University of Nigeria, Yola, NG

Published in Issue 2021-03-30

How to Cite

John, D., Chukwuneke, C. E., Onuigbo, I. O., Yahaya, M. F., Agboola, B. O., & Jahng, W. J. (2021). Low-temperature synthesis of kerosene- and diesel-range fuels from waste plastics using natural potash catalyst. International Journal of Energy and Environmental Engineering, 12(3 (September 2021). https://doi.org/10.1007/s40095-021-00387-z
Crossref
Scopus
Google Scholar
Europe PMC

Abstract

Abstract The current study tested the hypothesis of whether the low-temperature catalytic cracking of waste plastics would generate carbon fules using high-density polyethylene (HDPE) polymer by potash as a novel catalyst for both energy recovery and carbon recycling. We applied a one-stage pyrolysis reactor system with a 75 min reaction time to observe the highest yield at a low temperature range of 70–170 °C. The effects of the potash and zeolite catalysts, temperature, and catalyst–polymer ratio on the pyrolysis liquid yield and hydrocarbon contents were determined. The mineral concentration of potash was analyzed semiquantitatively using an inductively coupled plasma-optical emission spectrophotometer (ICP-OES) and X-ray diffractometer (XRD). The ICP-OES demonstrated that nine metals, in the order of K > Na > Fe > Si > Mg > Al > Cu > Ca > Ni, were predominant in the potash. GC–MS analysis of the liquid products showed that major catalytic cracking molecules are C 11 to C 20 as kerosene- to diesel-range liquid. Potash catalyst produced an average liquid conversion of 34.7% at a catalyst ratio of 30 wt% over a distillate temperature range of 76–140 °C, whereas zeolite generated 19.5% at the same catalyst ratio over 90–120 °C. Although the two catalysts favored mainly olefinic products, a higher potash ratio promoted a smaller carbon products with a purer composition. Our experiments demonstrated that the new natural potash catalyst could convert waste plastics into kerosene to diesel range of valuable and recyclable liquid products as potential renewable fuel sources for carbon recycling.

Keywords

  • Potash,
  • Zeolite,
  • Low-temperature catalytic pyrolysis,
  • HDPE polymer,
  • Waste plastics,
  • Alternative energy,
  • Carbon recycling

References

  1. Suhrhoff and Scholz-Böttcher (2016) Qualitative impact of salinity, UV radiation and turbulence on leaching of organic plastic additives from four common plastics: a lab experiment (pp. 84-94) https://doi.org/10.1016/j.marpolbul.2015.11.054
  2. Ferber et al. (2020) Ceramics from municipal waste incinerator bottom ash and wasted clay for sensible heat storage at high temperature (pp. 3107-3120) https://doi.org/10.1007/s12649-019-00617-w
  3. Dankwah et al. (2015) Recycling mixed plastics waste as reductant in ironmaking (pp. 73-80)
  4. Idumah and Nwuzor (2019) Novel trends in plastic waste management https://doi.org/10.1007/s42452-019-1468-2
  5. Miandad et al. (2016) Catalytic pyrolysis of plastic waste: a review (pp. 822-838) https://doi.org/10.1016/j.psep.2016.06.022
  6. Hassan et al. (2016) Recent progress on biomass co-pyrolysis conversion into high-quality bio-oil (pp. 645-655) https://doi.org/10.1016/j.biortech.2016.09.026
  7. Miskolczi et al. (2013) Comparison of real waste (MSW and MPW) pyrolysis in batch reactor over different catalysts. Part II: contaminants, char and pyrolysis oil properties (pp. 370-379) https://doi.org/10.1016/j.biortech.2013.06.109
  8. Fivga and Dimitriou (2018) Pyrolysis of plastic waste for production of heavy fuel substitute: a techno-economic assessment (pp. 865-874) https://doi.org/10.1016/j.energy.2018.02.094
  9. Kumar and Singh (2011) Recovery of hydrocarbon liquid from waste high density polyethylene by thermal pyrolysis (pp. 659-667) https://doi.org/10.1590/S0104-66322011000400011
  10. Vichaphund et al. (2015) Production of aromatic compounds from catalytic fast pyrolysis of Jatropha residues using metal/HZSM-5 prepared by ion-exchange and impregnation methods (pp. 28-37) https://doi.org/10.1016/j.renene.2014.10.013
  11. Ratnasari et al. (2017) Catalytic pyrolysis of waste plastics using staged catalysis for production of gasoline range hydrocarbon oils (pp. 631-637) https://doi.org/10.1016/j.jaap.2016.12.027
  12. Anuar Sharuddin et al. (2016) A review on pyrolysis of plastic wastes (pp. 308-326) https://doi.org/10.1016/j.enconman.2016.02.037
  13. Artetxe et al. (2013) Cracking of high density polyethylene pyrolysis waxes on HZSM-5 catalysts of different acidity (pp. 10637-10645) https://doi.org/10.1021/ie4014869
  14. Chen et al. (2014) Pyrolysis technologies for municipal solid waste: a review (pp. 2466-2486) https://doi.org/10.1016/j.wasman.2014.08.004
  15. Zaman et al. (2017) IntechOpen
  16. Sudi et al. (2016) Studies of some essential elements composition of potash deposits found in Yusufari local government area of Yobe State,Nigeria (pp. 1-6)
  17. Pedrotti et al. (2016) Changes in the floating plastic pollution of the mediterranean sea in relation to the distance to land (pp. 1-14) https://doi.org/10.1371/journal.pone.0161581
  18. Huang et al. (2019) Flotation of sylvite from potash ore by using the Gemini surfactant as a novel flotation collector (pp. 22-26) https://doi.org/10.1016/j.mineng.2018.11.055
  19. Rawashdeh et al. (2016) The potash market and its future prospects (pp. 154-163) https://doi.org/10.1016/j.resourpol.2016.01.011
  20. Al Rawashdeh and Maxwell (2014) Analysing the world potash industry (pp. 143-151) https://doi.org/10.1016/j.resourpol.2014.05.004
  21. Shao et al. (2010) Catalytic effect of metal oxides on pyrolysis of sewage sludge (pp. 1113-1118) https://doi.org/10.1016/j.fuproc.2010.03.023
  22. Nwankwor et al. (2020) Synthesis of gasoline range fuels by the catalytic cracking of waste plastics using titanium dioxide and zeolite https://doi.org/10.1007/s40095-020-00359-9
  23. Wong et al. (2017) Conversion of low density polyethylene (LDPE) over ZSM-5 zeolite to liquid fuel (pp. 71-82) https://doi.org/10.1016/j.fuel.2016.12.008
  24. Yousefi and Ghasemi (2020) Precipitator concentration-dependent opto-structural properties of MgO nanoparticles fabricated using natural brine https://doi.org/10.1007/s42452-020-2645-z
  25. Akubo et al. (2019) Aromatic fuel oils produced from the pyrolysis-catalysis of polyethylene plastic with metal-impregnated zeolite catalysts (pp. 195-202) https://doi.org/10.1016/j.joei.2017.10.009
  26. San You et al. (2000) Liquid-phase catalytic degradation of polyethylene wax over MFI zeolites with different particle sizes (pp. 365-371) https://doi.org/10.1016/S0141-3910(00)00130-0
  27. Fakinle et al. (2017) Changes in evaporative emissions from gasoline in the Nigeria market (pp. 1040-1046) https://doi.org/10.1080/10916466.2017.1305405
  28. Abbas-Abadi et al. (2013) Evaluation of pyrolysis product of virgin high density polyethylene degradation using different process parameters in a stirred reactor (pp. 90-95) https://doi.org/10.1016/j.fuproc.2012.09.042
  29. Marcilla et al. (2007) Study of the polymer–catalyst contact effectivity and the heating rate influence on the HDPE pyrolysis (pp. 424-432) https://doi.org/10.1016/j.jaap.2006.10.017
  30. Miandad et al. (2017) Plastic waste to liquid oil through catalytic pyrolysis using natural and synthetic zeolite catalysts (pp. 66-78) https://doi.org/10.1016/j.wasman.2017.08.032
  31. Seo et al. (2003) Investigation of catalytic degradation of high-density polyethylene by hydrocarbon group type analysis (pp. 383-398) https://doi.org/10.1016/S0165-2370(02)00186-9
  32. Marcilla et al. (2005) Study of the catalytic pyrolysis behaviour of polyethylene–polypropylene mixtures (pp. 387-392) https://doi.org/10.1016/j.jaap.2004.10.005
  33. López et al. (2011) Catalytic pyrolysis of plastic wastes with two different types of catalysts: ZSM-5 zeolite and Red Mud (pp. 211-219) https://doi.org/10.1016/j.apcatb.2011.03.030
  34. Li et al. (2017) Effect of ash composition (Ca, Fe, and Ni) on petroleum coke ash fusibility (pp. 6917-6927) https://doi.org/10.1021/acs.energyfuels.7b00850
  35. Aluri et al. (2018) Pyrolysis and gasification studies of model refuse derived fuel (RDF) using thermogravimetric analysis (pp. 154-166) https://doi.org/10.1016/j.fuproc.2018.06.010
  36. Sarker et al. (2011) Waste polyethylene terephthalate (PETE-1) conversioninto liquid fuel (pp. 1-5)
  37. Panda (2018) Thermo-catalytic degradation of different plastics to drop in liquid fuel using calcium bentonite catalyst (pp. 167-176) https://doi.org/10.1007/s40090-018-0147-2
  38. Ahmad et al. (2017) Pyrolysis of HDPE into fuel like products: evaluating catalytic performance of plain and metal oxides impregnated waste brick kiln dust (pp. 195-203) https://doi.org/10.1016/j.jaap.2017.02.005
  39. Chukwuneke et al. (2014) Synthesis of C5–C22 hydrocarbon fuel from ethylene-based polymers (pp. 805-809)
  40. Duan et al. (2009) Hydrodesulphurization performance of NiW/TiO2–Al2O3 catalyst for ultra clean diesel (pp. 187-191) https://doi.org/10.1016/j.cattod.2008.10.008